ADC Membership Technical Business Join ADC
Search Advanced Search
NOTE: This Technical Note has been retired. Please see the Technical Notes page for current documentation.

Technical Note DV16
Serial GPi (General-Purpose Input)

CONTENTS

This Technical Note discusses the latest supported methods for reading, validating, and configuring the GPi serial input across all members of the Macintosh family.

Updated: [February 01 1991]






What is GPi?

GPi is a software-configurable serial input present on some machines. It is located at pin 7 on the DIN-8 serial connectors, and connects to the DCD input of the Z8530 Serial Communications Controller (SCC). Because DCD is monopolized by the mouse on the Macintosh Plus, GPi is not implemented on that machine. Other machines which do not support GPi include the Macintosh Classic and Macintosh LC. On these machines, pins 7 of the DIN-8 serial connectors are not connected.

Back to top

Reading GPi (The Easy Part)

A number of developers currently make use of the GPi input on the serial ports of the Macintosh SE, Macintosh II, and Portable families. It's a handy feature and DTS regularly receives the question of how to read this input. The code required is actually quite simple, assuming all the proper hardware support is in place. As stated previously, some Macintosh models do not support GPi. For those machines which do support GPi and for which the SCC chip is directly accessible, the following code reads the state of GPi.

            movea   (SCCRd).w,a0   ; best place to get address of SCC RR0
            move.b  aCtl(a0),d0    ; modem port--use bCtl for printer port
            btst    #3,d0          ; GPi comes in DCD input--bit 3 of SCC RR0
            beq     @GPi0
    GPi1    ...
            ...
    GPi0    ...

This is currently the only way to determine the state of the GPi serial input. There is no support for this signal in the Serial Driver. If the SCC is not directly accessible, then neither is GPi. To determine if the SCC is accessible, check with _Gestalt. If an SCC exists but is not accessible, _Gestalt claims that there is no SCC.

Back to top

Validating and Configuring GPi (A Little Bit Harder)

To aid application developers in determining whether a machine supports GPi, a _Gestalt selector is available in System 6.0.7 and later. This selector is fully documented in Inside Macintosh, Volume VI, and specifies (a) whether GPi is supported on port A, (b) whether GPi is supported on port B, and (c) whether GPi may be used as a clock input for synchronous modems on port A.

There is another new call which developers can use to configure GPiA as an external clock. Previously, developers had to manipulate a bit in VIA1 to enable or disable external clocking on this pin. Unfortunately, there has always been some ambiguity about the sense of this bit (the SE uses the opposite sense of the Macintosh II) and the VIA bit is not present at all on the Macintosh IIfx--see Technical Note #271, Macintosh IIfx: The Inside Story. The friendly way to configure GPiA uses _HwPriv selector 7, as documented in that Technical Note.

MPW has never defined a high-level calling interface to this particular trap macro, and no glue has ever been available for Pascal and C programmers. Until this is remedied, the following inline glue fills in quite nicely:

    FUNCTION SwapSerialClock (clock, portID: Integer) : Integer;
      INLINE $205F, $7007, $A198, $6B02, $3008, $3E80;

    pascal short SwapSerialClock (short clock, short portID) =
    {
      0x205F, 0x7007, 0xA198, 0x6B02, 0x3008, 0x3E80
    }

For the normal 3.672 MHz internal serial clock, pass $0000 in the clock parameter. For external clocking provided at the GPiA pin, pass $0001 in the clock parameter. Other clock sources are theoretically possible, so use only one of these two values.

Only one value is currently supported for the portID parameter, and that is the Serial Driver enumerated constant sPortA. If necessary, this constant must be casted to type short or coerced to type Integer, according to the terminology of your development language.

If an error results, SwapSerialClock returns a negative number, otherwise it returns the previous GPiA configuration which is a non-negative number. This makes it convenient to save and restore the original state.

SwapSerialClock works with system software back to 6.0.5, although it does not achieve the desired results on the Macintosh IIfx. In fact, it may crash. This is a problem which is addressed in System Software 7.0. All the features described in this Note are technically new features for System 7.0, but Apple encourages developers to employ them if necessary (and available) in 6.0.x-compatible applications and suggest to their customers to use the latest available system software to obtain maximum benefit from these types of applications.

The following code fragment shows how to use these new features without explicitly depending upon specific system software versions. It assumes only that the _Gestalt trap is implemented or emulated by MPW glue (which is already available). It is not necessarily possible to trap the error of calling SwapSerialClock on a Macintosh IIfx with pre-7.0 software. It is best to avoid executing this code at all on such a configuration or else risk a system crash.

    PROGRAM SerialClock;

      USES Types,GestaltEqu,Serial;

      CONST
        internalClock = 0;     { convenient constants for SwapSerialClock }
        externalClock = 1;

      VAR
        gestErr    : OSErr;
        hasGPiAClk : Boolean;
        oldClockMode: Integer;
        result    : LongInt;

      FUNCTION SwapSerialClock(clock,portID: Integer): Integer;
        INLINE $205F,$7007,$A198,$6B02,$3008,$3E80;
      { this could be supported in a future version of MPW }

      BEGIN
        gestErr := Gestalt(gestaltSerialAttr,result);
        IF gestErr = noErr THEN BEGIN
          hasGPiAClk := (band(result,bsl(1,gestaltHasGPIaToDCDa)) <> 0);
          IF hasGPiAClk THEN BEGIN
            { SwapSerialClock is supported if gestaltHasGPIaToDCDa is supported }
            { it may experience difficulties with Mac IIfx and pre-7.0 systems... }
            oldClockMode := SwapSerialClock(internalClock,Integer(sPortA));
            IF oldClockMode < 0 THEN BEGIN
              { handle case of error setting the clock mode }
            END;
          END
          ELSE BEGIN
            { handle case where there is no GPiA clock support }
          END;
        END
        ELSE BEGIN
          { handle case where Gestalt doesn't know about serial attributes }
          { this usually means assume no support, or ask for later system... }
        END;
      END.

Back to top

References

Inside Macintosh, Volume III, The Macintosh Hardware

Inside Macintosh, Volume VI, Compatibility Guidelines

Guide to the Macintosh Family Hardware, Serial I/O Ports

Technical Note M.OV.GestaltSysenvirons - Gestalt and Sysenvirons : a Never Ending Story

Technical Note M.HW.MacIIfx - Macintosh IIfx: The Inside Story

Technical Manual: Z8530 SCC Serial Communications Controller (contact Zilog or AMD)

Back to top

Downloadables

Acrobat gif

Acrobat version of this Note (40K)

Download


Back to top


Technical Notes by Date | Number | Technology | Title
Developer Documentation | Technical Q&As | Development Kits | Sample Code




Gray line

Contact ADC |  ADC Site Map |  ADC Advanced Search
For information about Apple Products, please visit Apple.com.
Contact Apple | Privacy Notice
Copyright © 2002 Apple Computer, Inc. All rights reserved.
1-800-MY-APPLE